Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
Are you currently hunting for resources concerning Installing A Bathtub?

Setting up a tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open a wall surface to remove the old bathtub and position the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This post will help you mount a brand-new bath tub in your washroom if you have currently acquired a brand-new bathtub as well as don't require to change the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist should comprise the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be quite problematic due to the limited accessibility that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub until the level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water as well as check all joints and also new pipework for leakages as well as tighten them if needed. Fill the tub as well as likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, creating the water to pass through the wall in between the bath as well as the tiling, resulting in complications with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can break fairly early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article about How to Install a Bathtub through someone on a different web address. Enjoyed reading our article? Please share it. Let someone else find it. Thank you for your time. Don't forget to come visit our site back soon.
Stress-free? Call now! Report this page